Pinewood derby wheel alignment and rail riding
The fastest car doesn't roll perfectly straight. It steers gently into the guide rail and rides along it. That's called rail riding, and in our tools it edges out a car that rolls dead straight. A car with wheels pointing every which way finishes almost 8 car lengths behind. That's about a third of a second, from something that takes about an hour to fix.
Pinewood derby wheel alignment gets less attention than weight or shape, and crooked wheels cost more than a blunt shape does.
What the guide rail does
Look down a derby track and you'll see a raised strip running down the middle of each lane. That's the guide rail. The car's wheels sit on either side of it, and it keeps the car in its own lane.
A car with crooked wheels keeps steering into the rail, bouncing off, and steering back in. Every bump costs speed. A rail rider leans on one side of the rail and stays there, so it never bounces.
What the numbers show
Our wheel alignment tool races six identical cars on a 38 ft track. Compared with a car that rolls dead straight:
- Rail rider, steering gently into the rail on purpose: rubs it lightly the whole way, a few hundredths of a car length ahead.
- Dead straight: 2 rail hits. The yardstick.
- Straight-ish (pushed in carefully, never tested): 5 hits, about 2.7 car lengths behind.
- Bounces side to side: 14 hits, about 4 car lengths behind.
- Steers too hard into the rail: grinds along it the whole way, about 5 car lengths behind.
- Wheels every which way: 22 hits, almost 8 car lengths behind.
The rail rider and the grinding car both run along the rail. The difference is how hard they push on it. A gentle lean is rail riding. A hard pull from a crooked wheel is grinding, and it's one of the slowest cars on the list.
The worst car lost about a third of its energy to the rail and the wheels rubbing.
Perfectly straight almost never happens
The dead straight car is the ideal in our tools. In real life, it's almost impossible to build. A car that rolls straight across your kitchen floor can still wander once it's on a track.
Tracks aren't perfectly straight either. Ours has warped slightly after years of storage, and we straighten it out the night before every derby. Joints between track sections add small bumps too. A car trying to roll down the middle drifts into the rail on one side, then the other, and bounces every time.
That's why rail riding is the common advice for fast cars. A rail rider picks one side and stays there, so a warp or a joint doesn't knock it back and forth. You stop chasing a perfect car that nobody can actually build.
Pinewood derby wheel alignment, the simple version
A wheel steers the car in whatever direction it points. Nobody is steering a derby car, so a wheel that points a little sideways takes the car into the rail.
When the car hits the rail, some of its forward speed turns into a sideways bump and some turns into noise. None of it comes back. When a wheel grinds along the rail, it slows the car the whole way down. A light, steady rub costs much less than either.
Crooked wheels also wobble on the nails and rub against the car body. That's more friction on top of the bumping.
How to set up the wheels
Start by getting the wheels in straight. Every setup builds on that.
- Push each nail in square to the side of the car. A small square, or a block of wood with a straight hole drilled through it, helps.
- Leave a small gap between each wheel and the body. About the thickness of a business card. Wheels pushed in too tight rub the body.
- Make the gap the same on all four wheels.
- Do a roll test. Find a smooth floor or a long, flat board. Give the car a gentle push and watch it roll 5 or 6 feet.
- If it curves, nudge the front wheel on the side it curves toward. Small nudges. Roll it again until it rolls close to straight.
If your rules allow rail riding, set the car up to drift instead:
- Bend the axles slightly so the wheels lean in and ride against the nail heads instead of the car body.
- Set one front wheel so the car drifts slowly toward one side during the roll test. A slow, gentle drift. If it curves hard, it'll grind instead of ride.
Some races don't allow bent axles. Ask before race day, not at check-in.
Check the wheels again after painting. Handling the car while you paint can knock them out of line.
The tools use real physics, but the friction numbers are estimates, not measurements. The order of the cars is right. The exact decimals are our best guess.
On race day
At our derby, if a car jumps the track and it's the only one, we don't re-run the heat. If two cars are affected, we do. Wheels that are set up properly make a jump less likely.
Watch the rail from above
Our Wheel alignment tool races the cars from above, so you can see every bump against the rail. Pick Dead straight, Straight-ish, Bouncy or Crooked, then press Race.
The Advanced side adds the rail rider and the car that pulls, which is the race in the picture. It also has a slider for how hard the car steers into the rail. Too gentle and it still bounces. Too hard and it grinds. The chart shows the sweet spot in between, and you can switch the rest of the car from kit axles to fully tuned to see how the gaps change.
Wheels and axles go together. How to polish pinewood derby axles covers the other half.