Pinewood derby weight: why a 5 oz car is faster
Get your car as close to 5 oz as you can. Pinewood derby weight is the biggest and easiest thing you can change on your car. In our tools, four cars that are the same in every way except weight finish in weight order. The 5 oz car wins. The 3 oz car finishes about five and a half car lengths behind.
The rule
Pinewood derby cars typically have a 5 oz (142 g) limit, unless you're racing in a group with its own rules. Get as close as you can without going over.
People will ask to make heavier cars. Honestly, the answer is just no. Every car gets the same limit, and that's what makes it fair.
But doesn't everything fall at the same speed?
It does. Drop a marble and a bowling ball at the same time and they land together. On a perfect track with no friction and no air, a heavy car and a light car would tie.
A real track isn't perfect. Four things slow every car down:
- The air pushing back.
- The wheels rubbing against the car body.
- The car bumping the guide rail in the middle of the lane.
- The axles rubbing inside the wheels.
Pinewood derby weight, the simple version
Weight is your car's energy. The heavier the car, the more energy it has at the top of the hill.
The air, the rail and the rubbing slow every car down by about the same amount, whatever it weighs. A heavier car has more energy to push through them. It gets to the bottom with more left over, and more energy left over means more speed.
The axles work a little differently. A heavier car presses harder on them, so they slow it down a bit more. The other three don't change, so heavier still wins.
Here are the times from that race. Every car is built straight from the kit:
- 3 oz: 3.459 seconds
- 4 oz: 3.267 seconds
- 4.5 oz: 3.208 seconds
- 5 oz: 3.163 seconds
The last half ounce is still worth about 0.8 of a car length.
The numbers show one more thing. The better your car is, the less weight matters. On a fully tuned car, going from 3 oz to 5 oz is worth about 1.7 car lengths instead of 5.4. A well-built car has less friction to push through, so the extra energy makes less difference. A car straight from the kit needs the weight most.
How to add weight
Start by weighing what you have. A plain block with wheels and nails is about 4.3 oz in our tools, so it needs about 0.7 oz more. A sleek car with a lot of wood cut away is about 2.6 oz and needs 2.4 oz. A fancy shape means more weight to add, so plan for it.
- Use dense weights. Tungsten packs the most weight into the smallest space, so it's the easiest to hide. Steel and zinc weights are cheaper and bigger.
- Drill holes or a pocket for the weights, with an adult running the drill. Glue them in so they can't rattle or fall out.
- Cover them with wood filler and sand it smooth before you paint.
- Stop a little under 5 oz and bring some tungsten putty to check-in. Home scales don't always match the official scale, and it's easier to add a bit than to drill some out.
At our derby, I weigh every car at check-in and tell the family the number. Cars that need to gain or lose weight go to the pit stop, where the pit crew has tools to fix them. It's still easier to show up at 5 oz.
Once racing starts, it's hands off. No more adding or moving weight.
Where the weight goes matters too
Getting to 5 oz is step one. Where you put the weight is step two, and it can help or hurt a lot. Where to put weight on a pinewood derby car has the details.
Watch the gap open up
The race in the picture is our Mass tool. Pick a weight on the scale, press Race, and the faded cars show where each one was when the 5 oz car crossed the line. The 3 oz car is 5.4 car lengths back. That's about 3 feet of track.
Switch it to Advanced and you get a slider from 1 oz to 6 oz instead of buttons. Set it to what your car weighs today and race it against the others. You can also swap the rest of the car from kit parts to fully tuned, which shows the point above about well-built cars needing the weight less.