Skip to main content
← All Resources
Car buildingOctober 3, 2026 · 4 min read

Where to put weight on a pinewood derby car

Put the weight near the back of the car, about 1 inch in front of the rear axle. Not behind it. That's where to put weight on a pinewood derby car, and it's the spot our tools find fastest. Anywhere from 0.9 to 1.5 inches in front of the rear axle is the sweet spot.

Get it a little wrong and you lose a bit. Get it too far back and you lose a lot.

What "centre of gravity" means

Every object has one spot where it balances. That's its centre of gravity (center of gravity, if you're in the US). Some people call it the centre of mass. For a derby car, they're the same thing.

You can find it on your own car. Lay a pencil on the table and set the car across it, sideways. Slide the car back and forth until it balances. The spot sitting on the pencil is the centre of gravity. Measure from there to the rear axle.

Moving the weights moves that spot. Weights at the back pull it back. Weights at the front pull it forward.

The balance-point test in our centre of gravity tool. With the centre of gravity 1 inch in front of the rear axle, the car sits level on the point. That's the sweet spot, and it runs 3.145 seconds. Screenshot from our Centre of gravity tool →

Why the back is faster

A derby track starts with a steep hill. The car sits on the hill nose down, so the back of the car is higher than the front.

A car's speed comes from falling. What counts is how far its weight falls. Weight at the back starts higher up, so it has farther to fall. In our tools, weight at the back starts about 1.5 inches higher than weight at the front. That's about 3% more energy before the car even moves.

3% doesn't sound like much. On a kit car in our tools, moving the weight from the front to the sweet spot saves 0.05 seconds. That's about 0.8 car lengths.

A lot of advice online says weight placement is worth five car lengths or more. Our tools say it's worth closer to one. The big number usually includes adding the weight, not just moving it. The well-known test Dr. Scott Acton ran for Mark Rober's video measured "weight at 5 oz, at the back" together, and found about 5 car lengths. Our tools agree that adding the weight is the big part. So get to 5 oz first. Pinewood derby weight explains why.

Why too far back is a problem

At the bottom of the hill, the track bends from steep to flat, and the car goes through that bend fast. The front wheels get light there.

If the weight is in front of the rear axle, it holds the front wheels down. If the weight sits almost on top of the rear axle, nothing holds the front down, and it bounces at the bend. If the weight is behind the rear axle, the car tips back. The front wheels lift off, and the tail drags along the track.

The top car has its centre of gravity 0.3 inches behind the rear axle. It tips back onto its tail and runs 3.906 seconds, 14.1 car lengths behind the sweet spot. Screenshot from our Centre of gravity tool →

In our tools, that wheelie costs about 0.8 seconds. That's about 14 car lengths. A car with all its weight at the very front is much faster than that.

So the rule is back, but not too far back. Stay at least 0.9 inches in front of the rear axle and the front won't bounce.

How to put the weight where you want it

  • Plan the weight before you cut the shape. A thin, sleek car has less wood at the back for weight pockets.
  • Drill the weight pockets in the back half of the car, in front of the rear axle. An adult should run the drill.
  • Use dense weights like tungsten. They take less space, so it's easier to put them exactly where you want.
  • Before you glue anything, tape the weights on and do the pencil test. Move them until the car balances about 1 inch in front of the rear axle.
  • Glue them in, then do the pencil test one more time.

Bring a little tungsten putty to check-in for the last few tenths of an ounce. Put it near the back too.

The tools use real physics, but the friction numbers are estimates, tuned to published testing. Trust the order of things more than the last decimal.

Test it before you drill

Our Centre of gravity tool does the pencil test on screen. Press Near the front, Middle, Sweet spot and Too far back, and the car tips toward whichever end is heavy. Only the sweet spot sits level. Then race all four and see what each spot costs.

The Advanced side swaps the buttons for a slider. Drag it behind the rear axle and the car in the race lifts its nose and drags its tail, which is the 14 car lengths from the picture. Drag it back to about 1 inch and it wins again.