Skip to main content
← All Resources
Car buildingOctober 3, 2026 · 4 min read

Pinewood derby aerodynamics: does the shape of your car matter?

Pinewood derby aerodynamics matter a little. Less than you'd think. In our tools, a sleek car beats a plain block by 0.08 seconds on a 38 ft track. That's about 1.7 car lengths. It helps, but it's not where races are won.

That surprises people, because the shape is the part everyone sees. But the numbers put shape after weight and axles.

What the air is doing

When your car rolls down the track, it has to push air out of the way. The air pushes back. That push is called drag.

A plain block has a flat nose. The air hits it, piles up, and squeezes around the corners. Behind the car, the air swirls where the block ends square. Both of those cost a bit of speed.

A plain block in our wind tunnel. The orange lines are air piling up on the flat nose. The squiggles behind are the swirl off the square tail. It loses about 10% of its energy to the air. Screenshot from our Aerodynamics tool →

A sleek car has a low, rounded nose and a tail that comes down gently. The air slides over it instead of piling up.

The same car cut sleek. The air slides over the top, and the share lost to the air drops to about 2%. In the race, that takes it from 3.163 seconds to 3.079. Screenshot from our Aerodynamics tool →

How to change the shape

You change the shape with a saw and sandpaper. Get an adult to help with the saw. A few easy options:

  • Cut a wedge. One straight cut from a low nose up to the tail. In our tools, this gets you about two thirds of the gain by itself.
  • Round the nose. Sand off the front corners so there's no flat face.
  • Taper the tail. Let the back come down instead of stopping square.
  • Keep it low. A thinner car has less front for the air to hit.

Two things to watch. First, stay inside your rules. Most cap the car at 7 inches long, and many set a height limit too. Second, every cut takes wood away, so a sleek car needs more added weight to reach 5 oz. A plain block in our tools needs 0.7 oz of weights. A sleek one needs 2.4 oz. Plan where that weight goes before you cut. Where to put weight on a pinewood derby car covers that part.

Pinewood derby aerodynamics, the simple version

Drag grows fast with speed. Go twice as fast, and the air pushes back four times as hard. That's why shape matters so much for race cars and planes. They go really fast.

A derby car doesn't. Our tools put its top speed at about 10 mph, or 16 km/h. That's about how fast a kid rides a bike. At that speed the air barely pushes back.

The car starts at the top of the hill with energy from its height. On a car built straight from the kit, here's where that energy has gone by the finish line:

  • About 45% has turned into speed. That's the only part that wins races.
  • About 26% went to the axles rubbing.
  • About 19% went to the wheels rubbing the body and bumping the guide rail.
  • About 10% went to the air.

The air takes the least. A perfect shape can only win back part of that 10%.

The tools use real physics, but the friction numbers are estimates. Nobody has measured them part by part on a real derby car. We tuned them so a kit car and a well-built car finish in the times we see on a real 38 ft track, and checked the order of things against the testing Dr. Scott Acton did for Mark Rober's pinewood derby video. His tests found a streamlined shape was worth about 1.4 car lengths. Our tools say 1.1 for a wedge and 1.7 for a sleek car, so his number sits between them. That's close enough to trust the order of things, even if the last decimal is a guess.

So should you bother?

Yes. Just do it after the things that matter more. On a kit car in our tools:

  • Getting from 3 oz up to the full 5 oz is worth about 5.4 car lengths.
  • Polished axles with graphite are worth about 4.5 car lengths.
  • Putting the wheels in straight is worth about 3.9 car lengths.
  • A sleek shape is worth about 1.7 car lengths.

In our tools, a sleek car with kit axles loses to a plain block with polished ones, 3.079 seconds to 2.995. Do the axles first. Where to spend your time has the whole list in order, with how long each job takes.

Carve one in the wind tunnel

The pictures above come from our Aerodynamics tool. Press Block, Wedge, Bullet or Sleek, or drag across the car to cut your own shape, and the air changes as you cut. Then race your shape against a plain block, a wedge and a sleek car.

Switch to Advanced to see the drag number (Cd) and the front area after every cut, plus how much wood is left. That last number tells you how much weight you'll be adding back.