Skip to main content
← All Resources
EquipmentOctober 13, 2026 · 4 min read

How to set up a pinewood derby car photo booth

This is the pinewood derby car photo booth I use. It's a cardboard box, a sheet of poster board, some tissue paper and two clip-on reading lights. It is not the only way to do it, and I'm not going to tell you it's the right way. Plenty of people take great car photos with a phone, a window and a white sheet of paper.

What matters is that every car gets photographed the same way. Same background, same light, same angle, same distance. If you're turning the photos into cartoon icons, that consistency is most of the battle. Get it right and the whole roster looks like a matching set. Get it wrong and half the icons look like they came from a different event.

What you need

  • A sturdy cardboard box, about 12 to 16 inches on a side
  • White poster board for the inside
  • White tissue paper or parchment paper
  • Clear tape and scissors
  • A small block or box for a pedestal
  • Two compact clip-on LED reading lights, the kind with a bendy neck
  • A phone and a small tripod

If you don't have the right box, tape a few panels together, or use a plastic storage tote. For the background, poster board is the most durable and the easiest to replace when it gets scuffed. Layered heavy printer paper or a sheet of white craft foam also work. For the windows, tissue, parchment or a thin white cotton cloth pulled tight all do the same job.

Building the box

Cut a large window in both side panels and the top panel. Leave about a 1 inch border on every side so the box keeps its shape.

Tape tissue or parchment paper over all three windows. Pull it flat. These are your diffusion panels, and their whole job is to turn a small, hard light into a big, soft one.

Next, the sweep. Tape a sheet of white poster board to the top back edge inside the box and let it curve down to the floor and forward toward the opening, with no fold. That curve is why studio photos look like the object is floating on white. A sharp corner where the back wall meets the floor shows up in every photo as a grey line behind the car.

The pedestal

Wrap your small block in white paper so it matches the background. Set it in the middle of the sweep. The car sits on top.

Lifting the car a little off the floor of the box does two things. It gets the car away from the darkest part of the box, and it gives you a clean edge under the wheels.

Lighting is most of it

Clip one light to the top edge of each side window, on the outside of the box. Then angle them inward.

Don't point them straight at the car. Point them so the light comes through the tissue and hits the white back and side walls first. The light bounces around the box and wraps the car from every side, which fills in the low spots: the cockpit someone carved out, the gap behind the wheels, the underside of a spoiler. Light aimed straight at a glossy paint job gives you one bright hot spot and a hard shadow behind the car. Bounced light gives you even colour across the whole thing.

Turn the room lights down, or at least make sure the clip-on lights are doing most of the work. Ceiling lights, a window and LED reading lights are all slightly different colours (warm, blue-ish and somewhere in between), and the phone will average them differently from shot to shot. If your lights are the main source, every car comes out the same colour, and a red car stays the red its builder painted it.

Camera settings for a pinewood derby car photo booth

Put the phone on a tripod and leave it there. Don't move it between cars. Same position and same height for every shot is the single biggest thing you can do for consistency.

Set the lens at the same height as the middle of the car. Shooting from above makes the car look short and fat, and shooting from below makes it look like a monster truck. Neither is what the kid built.

Then lock focus and exposure. On most phones you press and hold on the car until the screen says it's locked (it's called AE/AF lock on an iPhone; Android phones vary by brand, so check yours). Without the lock, the phone re-guesses the brightness for every car. A white car comes out grey and a black car comes out washed out, because the phone is trying to make every photo average brightness. Locked, the phone takes your setting and keeps it.

Leave some white space around the car in the frame. If you're using the photos in Apex Derby, each one is cropped to a square before it becomes an icon, so a car that touches the edges of the photo loses its nose or its tail.

Why consistency matters for car icons

Apex Derby turns each car's photo into a cartoon icon of that car, and those icons show up on the display screen and on every parent's phone. The icon maker copies what it sees. A car photographed in clean, even light on white comes back as a clean icon. Anything else in the photo, like a kitchen counter, a hand or a coffee mug, can find its way into the icon too.

That's really the whole reason for the box. You're not trying to win a photography award. You're trying to give 40 or 50 cars the same fair start, the same way you'd want them on the track.

Running it at check-in

The booth fits on the end of the check-in table. One volunteer takes the car after weigh-in, sets it on the pedestal, takes the shot and hands it back. With the phone locked on the tripod, it takes me about 15 seconds a car to set it up and take the picture, and nobody has to think about settings once the first car looks right.

Take a test shot with the first car and look at it closely before you start the line. Check for a shadow behind the car, a grey line where the sweep meets the floor, and colour that matches the car in your hand. Fix those once, then leave everything alone.